12 August 2015

Carousel Washer Transaxle Parts – Case Study 21442

by bettereng1neer1ng / No Comments

Automotive Transaxle Parts Cleaning Carousel parts cleaning system with four (4) small turntables mounted to the large 60″ diameter carousel turntable. At any given time, one turntable can be loaded/unloaded by the operator while the other turntables are rotating in the wash, rinse, and dry zones. The unit outputs one set of clean/ dry parts […]

Read More

12 August 2015

Spline Shaft Conveyor Washer – Case Study 21872

by bettereng1neer1ng / No Comments

Spine Shaft Cleaning Compact conveyor washer designed to fit in customer’s existing work cell (between a knurling machine and a induction heating unit). The customer’s pick and place unit automatically places the shafts onto the washer’s conveyor. The parts get washed , blown-off and then slide down a chute into the customer’s vibratory conveyor.

Read More

12 August 2015

Drum Washer for Pharmaceutical Industry – Case Study 21429

by bettereng1neer1ng / No Comments

D-24 Rotary Drum Washer This cleaning system cleans small rubber parts after punch-out. Parts are automatically loaded and the drum tumbles the parts through the system. The parts are washed, dried, and then move onto the next stage. The D-24 has a super “clean design” to maintain sanitary conditions. All areas of the machine are […]

Read More

12 August 2015

Drum Washer to Clean Brass Shell Casings – Case Study 21132

by bettereng1neer1ng / No Comments

Background: This key corporation in the defense, aerospace, security and outdoor sport industries needed to clean 7.62mm brass shell casings in the manufacturing process. Problem: They were using 70 year old parts washers that no longer cleaned their parts efficiently or effectively.  They needed new washers to clean the shell casings after heat treatment. The […]

Read More

12 August 2015

Fuel Injector Parts Cleaning – Case Study 21780

by bettereng1neer1ng / No Comments

CJ-2 Tumbling Washer with Automated Conveyor This CJ-2 cleans fuel injector parts to the highest possible standards. This system cleans trays of parts since this is how they are normally handled in the manufacturing plant. The operator places a tray (single or double stacked) on the blue conveyor belt and walks away. The conveyor then […]

Read More

12 August 2015

Precision Cleaning Jet Engine Parts – Case Study 21805

by bettereng1neer1ng / No Comments

Parts Cleaning System RD-6000LX-PCS Twin systems designed for final, precision cleaning of critical jet engine components. These parts cleaning systems have a roll-in door and a spray/dry manifold that automatically lowers into the parts. Both the interior and exterior surfaces are directly impacted as the machines cycle through the following stages… wash, rinse, fresh rinse, and […]

Read More

12 August 2015

Jet Engine Exhaust Rings Parts Washer – Case Study 21480

by bettereng1neer1ng / No Comments

F-4000LX-PCS Parts Washer This customer makes various parts for jet engines and aircraft.  They purchased the F-4000LX-PCS parts washer shown to clean shrouds.  Each part is approximately 36” in diameter and 27” in height.  To clean the inner diameter to the same degree as the outer diameter, a powered spray/ dry manifold gets automatically lowered […]

Read More

11 August 2015

Long Spray Washer for Jet Engine Rotors – Case Study 21766

by bettereng1neer1ng / No Comments

Impulse Wide-80 The Impulse Wide-80 spray washer is designed to automatically clean jet engine rotors in a horizontal orientation. The work envelope is 80″ long x 33″ in diameter. This is a two (2) stage wash/dry system with spray and dry manifolds that oscillate around the rotor (the rotor remains stationary.) Plastic lined “V” fixtures […]

Read More